Sensorwell

MA233SAN

High Output VRS Sensor, Sealed Front End, 15,9 mm [0.625 in] M16 diameter, 175 Vp-p, -55 ºC to 150 ºC [-67 ºF to 300 ºF], 24 DP (module 1.06) or coarser, 15 kHz, 104 mm [4.10 in] approx. length

High Output VRS sensors are designed for use in applications where higher output voltages are needed. They perform best at low to medium speeds with medium to high impedance loads. Front-End Sealed versions are available for use where the sensor is exposed to fluids, lubricants or adverse environmental conditions.

Passive VRS (Variable Reluctance Speed) Magnetic Speed sensors are simple, rugged devices that do not require an external voltage source for operation.

A permanent magnet in the sensor establishes a fixed magnetic field. The approach and passing of a ferrous metal target near the sensor’s pole piece (sensing area) changes the flux lines of the magnetic field, dynamically changing its strength. This change in magnetic field strength induces a current into a coil winding, which is attached to the output terminals.

The output signal of a VRS sensor is an ac voltage that varies in amplitude and wave frequency as the speed of the monitored device changes, and is usually expressed in peak to peak voltage (Vp-p).

One complete waveform (cycle) occurs as each target passes the sensor’s pole piece. If a standard gear were used as a target, this output signal would resemble a sine wave if viewed on an oscilloscope.

Honeywell also offers VRS sensors for general purpose, power output, high resolution, high temperature, and hazardous location applications.

Jetzt anfragen!

MA233SAN

Produkt Merkmale

Kenndaten

  • Self-powered operation
  • Direct conversion of actuator speed to output frequency
  • Simple installation
  • No moving parts
  • Designed for use over a wide range of speeds
  • Adaptable to a wide variety of configurations
  • Customized VRS products for unique speed sensing applications
  • Housing diameters: 5/8 in (M16), 3/8 in (M12)
  • Housing materials/styles: stainless steel threaded or smooth
  • Terminations: MS3106 connector, preleaded
  • Output voltages: 8 Vp-p to 190 Vp-p

Anwendungsbereiche

  • Engine RPM (revolutions per minute) measurement on aircraft, automobiles, boats, buses, trucks and rail vehicles
  • Motor RPM measurement on drills, grinders, lathes and automatic screw machines
  • Motor RPM measurement on precision camera, tape recording and motion picture equipment
  • Process speed measurement on food, textile, paper, woodworking, printing, tobacco and pharmaceutical industry machinery
  • Motor speed measurement of electrical generating equipment
  • Speed measurement of pumps, blowers, mixers, exhaust and ventilating fans
  • Flow measurement on turbine meters
  • Wheel-slip measurement on autos and locomotives
  • Gear speed measurement

Technische Daten

Output Voltage (Peak to Peak) Min.
175 Vp-p
Operating Frequency
15 kHz
Diameter
15,9 mm [0.625 in]
Mounting Thread
5/8-18 UNF-2A
Material
Stainless Steel Threaded
Available Metric Thread
M16
Housing Length
104 mm [4.10 in]
Termination
MS3106 Connector
Operating Temperature
-55 °C to 150 °C [-67 °F to 300 °F]
Gear Pitch Range
24 DP (Module 1.06) or Coarser
Surface Speed
0,25 m/s [10 in/s]
Test Condition Specifications
Surface Speed = 25 m/s [1000 in/s], Gear = 20 DP [Module 1.27), Air Gap = 0.127 mm [0.005 in], Load Resistance = 100 kOhm
Coil Resistance
910 Ohm to 1200 Ohm
Pole Piece Shape and Size
Round; 2,69 mm [0.106 in] Diameter
Inductance
450 mH
Vibration
MIL-STD 202F, Method 204D
Weight
98 g [3.5 oz]
Comments
High resistance coils for maximum output voltage applications.
Series Name
High Output

Wir sind gerne für Sie da!

Jetzt kontaktieren

Unsere Partner

Kalsdorfer Straße 26 a
8073 Feldkirchen bei Graz
Österreich

Tel:    +43 316 40 33 01
Mail:  office@sensorwell.at